![]() If you got all the steps right up to this point, you should be able to pull it out easily. Once the release pin that secures the ignition switch is released, you can pull it out from its position. There should be a tiny hole to insert the screwdriver and press down on the release pin inside. Start by pressing the release pin inside the hole on the ignition module with the screwdriver. If you have to use a flathead screwdriver, then you’d need to be careful. If you don’t have access to your car key at the moment, you might need to use a flathead screwdriver instead. It is necessary to do this because this is the only way to release it from the ignition module. Set the key in the ignition and turn it to the “accessory” position. Step 6: Keep the Keys in the Right Position You might need a screwdriver to be able to press down the release mechanism on the hooks. There should be some releases on the clips. This allows you to take away the cover so that you can access the ignition switch. Unlock the hooks on the ignition module cover. Step 5: Free Up the Ignition Module Cover Or better still, get an ignition switch panel wiring diagram for your car. It is important that you consult the repair manual for your vehicle before undergoing this step. ![]() You might need to do this using a steering wheel puller to make your task easier for you. Regardless of its location, removing the steering column will make your job a lot easier. Some vehicles have their ignition switch in the dashboard, while others might have it along the steering column. Once you have taken them off, keep them somewhere safe where they won’t get damaged. You might have to remove them by taking off the plastic clips, securing them, or unfastening any bolts or screws. Take away any trim that might be around the steering wheel. Ensure that you secure the negative cable safely to prevent it from coming in contact with any of the terminals in the course of wiring the ignition. Use a wrench to loosen the bolt before disconnecting the battery terminals. There are two terminals marked positive (+) and negative (-) on your vehicle’s battery. Step 3: Disconnect the Battery Terminalsĭisconnect the negative terminal on the battery. Depending on the car, you’d find four terminals that are marked as “BATT”(Battery), “ST” (Starter), “IGN”(Ignition input), and “ACC”(Accessory).To be on the safe side, get some confirmation from your car’s repair manual or the manufacturer. Step 2: Ascertain the Terminals on the Ignition SwitchĪscertain and locate the pins on the back of the vehicle’s ignition switch. Step 1: Park the VehicleĮnsure that your vehicle is parked on level ground before turning off the engine. However, depending on the vehicle in question, you might need a push-button starter switch wiring diagram. Here are the steps you need to take to wire the ignition switch yourself. The BATT typically has a red wire, while the other three wires may have green, white, and black colors. Therefore, it’s essential you go based on where the wires are connected instead of the colors. The wire colors will vary depending on your car make and model. You must understand which wire goes to where in the ignition switch if you are planning to troubleshoot or replace it. The ACC usually has a purple-coated wire. The ACC terminal transmits power to the car accessories like the radio, the lights, the windshield wiper, and many others. It usually has yellow or brown coated wire, depending on your car.ĪCC (Accessory). The ST terminal sends electric flow to the starter solenoid. It’s usually connected with a red or yellow wire, depending on your car model. This terminal controls and distributes power to the ignition and other car electronic components. The BATT is the terminal to which a thick wire with a red coating connects to. So, if you have a new modern ride, you have four wires in the ignition switch, labeled īATT (Battery). New modern vehicles usually have four wires in the ignition switch. But first, let’s see the wires that go to the ignition switch. This article will walk you through the steps needed to wire your vehicle’s ignition switch. Thankfully, it is not a complicated process to handle once you have the know-how. You never know when it might fail, so you need to understand how to wire the ignition switch. Replacing the ignition switch becomes imperative when it becomes difficult to turn on the vehicle’s electrical system or when it fails to signal the starter motor to stop turning once the engine starts running. ![]() The ignition switch is responsible for turning on the circuits or signals that get the vehicle to start.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |